InformationUsed Car Export Car Inspection Content
Manual inspection
(1)Whether it belongs to the prohibited export vehicle type
Exported used vehicles that meet the scrapping standards specified in the “Motor Vehicle Mandatory Scrapping Standards” and have been used for less than 1 year (including 1 year) according to the specified requirements shall not be inspected.
(2)Basic inspection
The inspected motor vehicle should have no obvious oil, water, or gas leaks, the tires should be intact with normal tire pressure, the tire sidewalls should be intact without cracks, the engine should run smoothly, and there should be no faults related to the Anti-lock Braking System (ABS), Electric Power Steering (EPS), and other safety-related systems.
(3)Car uniqueness check
According to the “Vehicle Registration Certificate” and “Vehicle Registration Certificate,” check the vehicle type, brand/model, vehicle identification number (or vehicle model and factory number), and engine number of the inspected motor vehicle.
Determine the main characteristics and technical parameters of the motor vehicle (outer dimensions, wheelbase, curb weight, approved seating capacity, railing height, rear axle leaf spring number, emergency exits for buses, passenger passages and aisles, cargo compartments), and calculate the rear overhang for trucks to confirm whether it matches the content recorded on the certificate and vehicle product label.
For trucks, trailers, and buses longer than 6 meters, relevant length, width, and height dimensions should be measured, and the vehicle identification number (or whole vehicle factory number) and engine number should be checked for signs of alteration.
(4)Car Exterior Inspection
① The interior and exterior of the vehicle (cabin) should be free from obvious defects that affect driving safety and require rectification.
② Check if the cargo compartment installation is secure, whether the railings and floorboards are neat and the strength is sufficient, and whether the safety frames are intact.
③ Check if the passenger car has front and rear bumpers, if the truck has a front bumper, and whether they are intact.
④ Check the reliability of the fixing of the folding cab.
⑤ The tire specifications should match the vehicle registration information. The wheel hub should not have obvious deformation, and the tire tread and sidewall should not have cracks and cuts exceeding 25mm in length or depth sufficient to expose the tire cord layer, as well as other defects, abnormal wear, bald spots, and deformations affecting use.
⑥ For trucks with a total weight greater than 3500kg, specialized operation vehicles with modified truck chassis, and trailers, the side and rear lower protective devices should be normal and effective, and the side protective devices between the tractor and trailer of truck trains should be normal and effective.
(5)Lighting and Electrical Signaling Devices
① Check if the front lighting and signaling devices, including front position lamps, front turn signal lamps, front hazard warning signal lamps, clearance lamps, and trailer identification lamps, are complete and functioning properly, and if the high and low beam switching function of the headlights is normal.
② Verify if the rear lighting and signaling devices, including rear position lamps, rear turn signal lamps, rear hazard warning signal lamps, clearance lamps, brake lamps, rear fog lamps, rear registration plate lamps, reverse lamps, and rear reflectors, are complete and functioning properly.
③ Ensure if the side turn signal lamps, side marker lamps, and side reflectors are complete and functioning properly.
(6)Engine Compartment
① Open the engine hood (or flip the cab) and visually inspect all visible engine systems and components to ensure they are complete and functional. Check if the battery terminals are securely connected to the wires, and examine the bundling, fixing, and insulation protection of visible electrical wires. Ensure that all types of pipelines are intact, securely fixed, and free from flammable materials.
② For vehicles equipped with hydraulic brakes (including hydraulic transmission clutches), visually inspect the fluid level in the reservoir and check for any leaks.
(7)Engine Operation
① Check if the engine can start normally. Start the engine and inspect the idle operation, power charging status, and the normal functioning of all gauges and indicators. Check if the engine can return to idle state smoothly when the throttle is released abruptly during rapid acceleration and at high RPM, and whether there are any abnormal conditions such as “backfiring” or “misfiring”. Inspect for any leaks of water, oil, or air, and ensure that the water temperature and oil pressure indicators are normal. Check if the engine can quickly turn off after the ignition switch is turned off. For diesel vehicles, also check if the shutdown device is flexible and effective.
② During engine operation and parking, there should be no leakage from the radiator, water pump, cylinder block, cylinder head, heater, or any connecting parts.
(8)Interior Inspection
① Check if there are any sharp protrusions inside the vehicle that could cause injury (such as sharp corners or edges).
② Check if the door locks and hinges are functioning properly; ensure that the door locks lock and unlock both from the inside and outside normally.
③ Ensure that all seats are equipped with effective seat belts, and verify that the seat belts are complete and functional.
④ All windows and windshields should be intact.
(9)Chassis Dynamic Inspection
① Steering System:
Check if the vehicle has automatic self-centering capability and the ability to maintain straight-line driving while in motion.
② Transmission System:
During vehicle operation, check if:
The clutch operates smoothly and normally.
③ Brake System:
Drive straight at a speed of about 20 km/h, lightly hold the steering wheel with both hands, then quickly release the brake pedal after braking firmly. Preliminarily assess the coordination time, release time, and whether there is any deviation during braking. For pneumatic brake vehicles, depress and release the brake pedal several times to lower the brake air pressure to below the starting pressure (if not specified, use 400 kPa), and check if the low air pressure alarm device is activated.
④ Gauges and Indicators:
During the chassis dynamic inspection, the inspector should pay attention to observing if there are any abnormal conditions with various gauges and indicators installed in the vehicle.
⑤ After continuous driving of the motor vehicle, observe all components to ensure there are no leaks.
(10)Inspection of Vehicle Chassis Components
① Steering System Components:
All components should not be loose.
There should be no interference or friction during steering.
② Transmission System Components:
Components such as the gearbox should be securely connected.
The transmission shaft, universal joint, intermediate bearing, and support should not have cracks or looseness, and there should be no obvious oil leakage.
③ Driving System Components:
The longitudinal and transverse beams of the chassis should not have obvious deformation or damage, and rivets and bolts should not be missing or loose.
The rods and guide rods between the axle and suspension should not be loose or displaced.
④ Brake System Components:
The brake master cylinder, wheel cylinder, brake lines, etc., should not have air or oil leakage, and the brake hoses should not be cracked, flattened, or bulging.
There should be no friction or loose fixation between the brake system pipelines and other components.
⑤ Other Components:
The engine mounting should be reliable.
The exhaust pipe and muffler should be securely installed.
The fuel tank should be securely fixed and should not leak oil; there should be no rubbing between the fuel pipeline and other components.
Related articles：
Concepts and processes related to China’s used car export
What conditions do enterprises need to meet to export used cars in China?
In China, what kind of cars are prohibited from being exported?
InformationIn China, what kind of cars are prohibited from being exported?
Nowadays, the car export business in China is booming. The majority of it is parallel export, which means first purchasing brand new cars and then exporting them in the form of used cars.
In order to safeguard various interests and ensure safety, the Chinese government has imposed some necessary restrictions on the export of used cars.
The following are the circumstances under which the export of used cars is prohibited
(1) Vehicles that meet the scrapping standards specified in the “Motor Vehicle Mandatory Scrapping Standard Regulations” and vehicles that have been used for less than one year (including one year) from the prescribed scrapping deadline;
(2) Vehicles under mortgage, pledge, or under customs supervision;
(3) Vehicles that are seized or detained by supervisory organs, people’s courts, people’s procuratorates, or administrative law enforcement departments in accordance with the law;
(4) Vehicles obtained through illegal and criminal means such as theft, robbery, or fraud;
(5) Motor vehicles with discrepancies between the information recorded in the motor vehicle registration certificate and the actual vehicle;
(6) Smuggled or illegally assembled vehicles;
(7) Vehicles with incomplete statutory certificates or vouchers;
(8) Vehicles with unqualified inspection results;
(9) Vehicles with unresolved road traffic safety violations or traffic accidents;
(10) Other vehicles prohibited from trading or exporting by laws and regulations.
The above are the standards for cars prohibited from export. If you don’t know where to buy a reliable car, then you’ve come to the right place on our website.